Have your say & ask the experts

I need an AV stand. I thought I'd buy something and then read the threads by Ray Palmer. What the hell, I'll make one. Don't get me wrong. I know that there isn't the technical challenge of Ray's threads but nonetheless it will not be without difficulties.

So, In this thread I'll document the steps taken from design through to completion of the stand.

More to follow.....

Will this be a Plywood or solid timber affair?

I can recccomend some good wood glue too!

Solid wood. The construction is well underway. The photos and thread need to catch up!

If you're going to be gluing some of the joints to re-inforce them then I suggest using a glue called "Titebond". I used to use this in my failed attempt to become a luthier aand although I failed all the bits I stucck together are still holding together!

Very high tack and aggressive nite though so it's a great glue.

OK. Time for an update!

I wanted something heavy in wood. Looked around at the options but nothing really fitted what I wanted (in terms of design) or my budget.

So, I drew out a design

I know. You're all impressed. However, It does give me enough information to start fleshing out ideas, materials, etc.

I first looked at solid oak kitchen worktops like this

These turn out to be a little on the expensive side....and I didin't know if my design would actually work. The key concern for me was the width of the unsupported span.

As a cheaper alternative, I decided to go for some of this

This is 40x70mm softwood. Fabricating the board from this timber is a little daunting and I have never done it before. But it can't be that hard, can it?

More updates to follow.....

Cool!

If you get stuck I'm sure Vanman would be willing to help out....then again possibly not.

You could always go the Blue Peter route and stick it together with a bit of sticky back plastic  . Or for the full on effect you would also have to use toilet rolls and the odd empty washing up liquid bottle.

Seriously though good luck with your project

Mental note to self to update this thread!

OK, long overdue update and I've forgotten the associated narrative I was planning to use to support the photos. Still, here goes.....

I bought a shed load of 4x2 planned timber and some 1/4" plywood from B&Q. What I needed to do was cut all the 4x2 to length and join all the 4x2 together to form the sides, top and shelves. I wanted a strong joint, so decided to route a small slot in the side of each length of 4x2 and use the a 1/4" plywood fillet to strengthen the joint.

Routing the lengths of 4x2 to introduce the slot for the fillet.


A part glued shelf showing the plywood strengthening fillet. The fillets were ripped down from a sheet of plywood using a bandsaw.


The slotted 4x2 complete with plywood fillets then needed to be glued and clamped. I glued three lengths together at a time, slowly building up the sides, top and shelves. I used Bessey clamps....expensive but just about the best you can get. You need a lot of clamps!


I then routed the sides to accept the shelves and the top to accept the sides (not shown).

I then routed a further slot to fit in a plywood fillet to strenghten the joint between the sides and the shelves and the sides and the top (not shown).


I then glued the sides, shelves and top together and sanded the whole lot down. If you're in the market for a orbital sanded I can highly recommend the metabo duo and DM Tools as a supplier of all DIY tools.


Next was the finishing. I agonised over this. In my experience, this is where it all goes wrong. I finally went for this stuff.


I then applied the finshing products to the stand, giving it a couple of coats and then giving it a good polish and that's the finished stand!


This thing is immensely strong and heavier than the average stand. The stats are...

Component	Length of 4x2 (mm)	Estimated Weight (Kg)
Top	8260	8.26
Sides	7576	7.58
Shelves	12180	12.18
Total	28016	28.02

Note: I estimated the weight by weighing a short length of 4x2 and established that the timber weighs approximately 1g per mm.

I have to say I am quite pleased with the results but it was a fair amount of work. It ended up costing about a ton.

Not sure I like the colour much. It's supposed to be light oak but it has the inevitable orangey look about it. Still, this is a temporary stand.

In the near future, now that I have validated the design, I will use oak kitchen worktops instead. Expensive, but I won't have to fabricate the board.

nice work pj, very informative post,given me some ideas now, why not use vaneered mdf as an alternative to oak work tops, be much cheaper